What is Geotechnical Engineering ????????????????????

It is the art and the science of utilizing the scientific principles of the soil mechanics, rock mechanics, soil dynamics, and engineering geology to analyze and design different soil and soil-structure interaction systems.

This, however, requires skill and knowledge to

1- Identify and describe rock & soil types
2- Identify and describe rock & soil formations
3- Identify ground water conditions.
4- Recognize the potential for the passive impact on the proposed project.

The general objectives of the Geotechnical Investigation are:

1- Define lateral distribution of soil layers
2- Define groundwater conditions
3- Identify geologic hazards
4- Procure samples
5- Perform In-Situ testing (SPT or CPT)

6- Determine soil and rock properties 

1- Site Exploration

The general objectives of the exploration program for any project are:

1- Define the depth of the proposed foundation
2- Evaluate the load-bearing capacity of the foundation
3- Estimate the probable settlement
4- Identify potential foundation problems
5- Define ground water conditions
6- Predict lateral earth pressure
7- Establish method of construction
8- Determine suitability of the site material for construction

The site exploration program should include the following:

1-1 Data Collection	1- Type of structure 2- General use of the structure 3- Column load 4- Column spacing 5- Building code 6- Basement requirements 7- Topography maps 8- Geologic maps 9- Soil maps 10- Groundwater maps 11- Reports, Aerial photographs, satellite images, etc
1-2 Terrain Analysis	Using remote sensing and landform interpretation techniques to determine: 1- Geomorphic characteristics of the site (Landform) 2- Relief amplitudes 3- Drainage basins 4- Vegetation 5- Climate conditions, weathering, frost action, erosion, and mass wasting.
1-3 Site Reconnaissance	Is a field trip to inspect: 1- General topography, existing of drainage, ditches, etc. 2- General conditions of the soil 3- Type of vegetation 4- Surface water condition 5- Accessibility of the site
1-4 Subsurface Sectioning	This includes the following: 1- Seismic refraction (For large areas) 2- Test pits (for shallow depths) 3- Auger boring (Manual, Mechanical) 4- Wash boring 5- Core boring The depth and the interval of the subsurface sectioning is governed by: 1- Type of construction 2- Column Load 3- Column Spacing Test boring is the most usable method In planning and executing the test Boring you need to know: 1- Equipment Selection 2- Boring Spacing 3- Boring Depths	1-4-1. Equipment Selection This depends on: 1- Terrain features 2- Accessibility 3- Geologic Conditions 4- Boring depths 5- Sample types 6- Nature of the project 1-4-2. Boring Spacing Depending on the area under study. Grid systems may be appropriate in uniform conditions. The spacing usually range from 30 ft to 1600 ft. The following spacings may be adopted for wide range of constructions: 1- Multistory buildings --------- 30 ft to 100 ft 2- Residential subdivision -------- 800 ft to 1600 ft 3- Warehouses, Industrial plants --------- 60 ft to 200 ft 4- Dams and Dikes --------- 130 ft to 260 ft 5- Highways and railways -------- 800 ft. to 1600 ft. In general spacing may vary depending on the irregularity of the site geology. 1-4-3. Depth of Boring 1- Boring should be extended through any unsuitable foundation strata (unconsolidated fill, organic soils, compressible layers) until soil of acceptable bearing capacity is reached. 2- In general, boring should be extended to at least 1.5 to 2 times the minimum width of the loaded area. 3- In the case of vary heavy structures (bridges), boring in most cases are extended to bed rock, or at least one boring should be extended to bedrock. 4- The following empirical equations can be used to estimate the minimum depth of borings in office buildings: Dboring = 3 S0.7 (for light steel or narrow concrete buildings) Dboring = 6 S0.7 (for heavy steel or wide concrete buildings) where S = number of stories in meter
1-5 Sample Recovery	1-5. SAMPLE RECOVERY Soil samples obtained during subsurface sectioning are either: 1- Disturbed 2- Undisturbed Disturbed soil samples are used for: 1- Grain size analysis 2- Determination of index properties 3- Organic content 4- Specific gravity Undisturbed samples are used for: 1- As above 2- Determining mechanical properties 3- Determining hydraulic properties 1-5-1 Methods Of Sample Recovery 1- By hand 2- Split spoon 3- Scraper bucket 4- Thin wall tube (shelby tube) Split spoon sampling method is used to obtain disturbed and undisturbed samples. - The sampler is driven into the soil by a hammer. - The weight of the hammer is 140 lb. - The number of blows (N) required to penetrate the spoon of three 6 in. intervals are added and recorded. This procedure is called the Standard Penetration Test (SPT) - Actually, the Standard Penetration Number N is the number of blows (N) of the last two intervals (12 in). The first interval (6 in.) is usually discarded (why ????????????).	THE STANDARD PENETRATION TEST (SPT)   - The SPT which was developed in 1902 by Colonel Charles Gow of the Raymond Pile Company. Karl Terzaghi in 1947 recommended seating correction for the SPT values. - It  is currently one of the most popular and economical in situ test to obtain subsurface information. - It is estimated that 85% to 90% of conventional foundation design in the USA is made using the SPT. - The testing method was standardized in 1958 as ASTM D1586. - The test consists of: 1 - Using a 140 lb driving mass (W) falling free from a height of 30 in. (h)  to 2 - Drive the standard split spoon sampler a distance of 18 in. into the soil, and 3 - Counting the number of blows (N) to drive the sampler 12 in. (6 in. + 6 in.). Theoretical free-fall energy of the SPT hammer Etheo = W.h          = (140 lb)(30in) = 4200 in-lb. - The boring log should show "refusal" and should be halted if: a- 50 blows are required for any 150 mm increment b- 100 blows are obtained c- 10 successive blows produced no advance. - N should be corrected for the increase of the overburden pressure Relative Density of Coarse-Grained Soils Number of Blows (N) Classification Dr (%) 0 - 4 Very Loose 0 - 15 4 - 10 Loose 15 - 35 10 - 30 Medium 35 - 65 30 - 50 Dense 65  - 85 > 50 Very Dense 85 - 100                                                                                                                                             (after Terzaghi & Peck 1948)